Informācijai: Pasūtījumi veikti periodā no 16.05.24 līdz 23.05.24, tiks apstrādāti 24.05.24. Atvainojamies par sagādātajām neērtībām!

Specification:

SpeedyBee F405 V3 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): BMI270

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

Blackbox MicroSD Card Slot

BetaFlight Camera Control Pad: Yes(CC pad on the front side)

Current Sensor Input: Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.

Power Input 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.

9V Output" 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART" 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection), UART5(Dedicated for ESC telemetry)

I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

Supported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV

Firmware Target Name: SPEEDYBEEF405V3

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 9.6g


SpeedyBee BLS 60A 30x30 4-in-1 ESC

Firmware: BLHeli_S J-H-50

PC Configurator Download Link: https://esc-configurator.com/

Continuous Current: 60A * 4

Burst Current: 80A(10 seconds)

TVS Protective diode: Yes

External Capacitor: 1000uF Low ESR Capacitor(In the package)

ESC Protocol: DSHOT300/600

Power Input: 3-6S LiPo

Power Output: VBAT

Current Sensor: Support (Scale=400 Offset=0)

ESC Telemetry: Not supported

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 45.6(L) * 44(W) *8mm(H)

Weight: 23.5g


Package Included:

1x SpeedyBee F405 V3 Flight Controller 

1x SpeedyBee BLS 60A 4-in-1 ESC 

1x 35V 1500uF Low ESR Capacitor 

5x M3 Nylon Nut 

5x M3 silicone O Ring

5x M3*8mm Silicone Grommets(for FC)

5x M3*8.1mm Silicone Grommets(for ESC)

1x SH 1.0mm 15mm-length 8pin Cable(for FC-ESC connection)

5c M3*30mm Iner-hexagon Screws 

1x DJI 6pin Cable(80mm)

1xXT60 Power Cable(70mm) 


Manual/wiring

Uzrakstīt atsauksmi

Lūdzu login vai register lai atstātu atsauksmi

SpeedyBee F405 V3 + 60A BLS ESC 30x30 Stack

  • Ražotājs: RunCam
  • Produkta kods: F4V3-60-Stack
  • Pieejamība: Noliktavā
  • 73.90€

  • bez PVN: 61.07€