Specification:

SpeedyBee F405 V3 30x30 Flight Controller

MCU STM32F722

IMU(Gyro) BMI270

USB Port Type Type-C

Barometer BMP280

OSD Chip AT7456E chip

BLE Bluetooth Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip

Flash FC Firmware Wirelessly Supported. Please enter MENU > FC Firmware Flasher

Download/Analyze Blackbox Supported.Please enter MENU > Blackbox Analyzer

DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.

Flash(for BlackBox) 500MB

BetaFlight Camera Control Pad Yes(CC pad on the front side)

Power Input 3S - 6S Lipo

5V Output 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.

9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.

3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal Pads M1 - M4 on bottom side and M5-M8 on front side.

UART 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)

ESC Telemetry UART R4(UART4)

I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.

LED Pad Used for WS2812 LED controlled by Betaflight firmware.

Buzzer BZ+ and BZ- pad used for 5V Buzzer

BOOT Button Supported.

[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.

[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.

RSSI Input Supported. Named as RS on the front side.

SmartPort Supported

Supported Flight Controller Firmware BetaFlight(Default),INAV

Firmware Target Name SPEEDYBEEF7V3

Mounting 30.5 x 30.5mm( 4mm hole diameter)

Dimension 41(L) x 38(W) x 8.1(H)mm

Weight 10.7g

SpeedyBee BL32 50A 30x30 4-in-1 ESC

Firmware SpeedyBee BL32 50A

Configurator Download Link http://github.com/bitdump/BLHeli/releases

Continuous Current 50A * 4

Burst Current 55A(5seconds)

TVS Protective diode Yes

Heat Sink Yes

External Capacitor 1000uF Low ESR Capacitor(In the package)

ESC Protocol DSHOT300/600

PWM Frequency Range 16KHz-128KHz

Power Input 3-6S LiPo

Power Output VBAT

Current Sensor Support (Scale=490 Offset=0)

ESC Telemetry supported

Mounting 30.5 x 30.5mm( 4mm hole diameter)

Dimension 45.6(L) * 40(W) * 8.8mm(H)

Weight 19.2g with heat sink

Package Included:

1x SpeedyBee F7 V3 Flight Controller 

1x SpeedyBee BL32 50A 4-in-1 ESC 

1x 35V 1500uF Low ESR Capacitor 

5x M3 Nylon Nut 

5x M3 silicone O Ring

5x M3*8mm Silicone Grommets(for FC)

5x M3*8.1mm Silicone Grommets(for ESC)

1x SH 1.0mm 15mm-length 8pin Cable(for FC-ESC connection)

5c M3*30mm Iner-hexagon Screws 

1x DJI 6pin Cable(80mm)

1xXT60 Power Cable(70mm) 

Manual/wiring